RAID Recovery™
Recovers all types of corrupted RAID arrays
Recovers all types of corrupted RAID arrays

RAID 5 Data Recovery

The problems with your data are always spontaneous. Regardless of how well you prepared for blackouts, or virus attacks, when data loss happens, you will probably need some help. Your very first question will probably be:

How RAID 5 disk recovery is provided?

First of all, calm down and realize that there is recovery software available that is able to save as much of your data as possible. If you are calm and ready to take the next steps, go to the next sections of this article, where you will be provided with proper instructions on how to recover RAID 5.

The first thing you need to determine before RAID 5 data recovery is RAID 5 array configuration.

It usually consists of the following parameters:

  • The quantity of disks your RAID 5 contains. The minimal number for RAID 5 is three.
  • The disk sequence within an array.
  • The stripe size used in your RAID 5.

RAID 5 recovery

This scheme is an example of a classic RAID 5 containing four disks. The basic understanding of your RAID will be helpful before you start finding out how to recover RAID 5 data.

But if you don’t understand anything in tech, don’t worry. Diskinternals recover data RAID determines the configuration of an array automatically, and it takes a couple of minutes if proceed in the Reader/Uneraser mode. The next paragraph will be dedicated to an automatic way of RAID 5 disk failure recovery.


RAID-5 recovery with software

The main thing to do to prevent data loss is backing up your data on a regular basis. BUT! If you don't have any backup - it is not a problem with DiskInternals RAID Recovery. Using RAID Recovery you can restore your data from RAID 5, regardless of loss reason.

If you have encountered problems with RAID-5 recovery, you can restore data with RAID Recovery by DiskInternals. This software will be able to save the information and transfer it to a new location.

Detecting disk configuration and technical parameters can be made automatically or manually. All you need is to follow the step-by-step guide provided below just for you.

RAID 5 recovery with 2 Failed Drives

RAID 5 users frequently have troubles with data recovery, regardless of array size. You will need the most powerful RAID recovery software to perform data recovery from the RAID 5 array because of complicated mechanisms of data storage. The good news is that RAID Recovery by DiskInternals can perform RAID 5 data recovery.

Again, if you cannot even remember when your last backup was made, the possibility of recovering your information, and, moreover, the functions of the applications you had, will probably not be restored. But you can try saving data anyway.

RAID Recovery by DiskInternals will make everything possible to save the maximum amount of information from your RAID 5 array.

Manual for RAID 5 recovery

If you are facing the problem of data loss, and you have never restored data before, below you will find a learning video. It has step-by-step guides that might help you to understand the RAID 5 data recovery process and make it easier.

The first tip is using the Diskinternals RAID recovery software in the Reader/Uneraser mode because otherwise, you will spend a lot of time on disk checking.

RAID 5 Recovery Guide:

The second tip about RAID 5 recovery is, never try to restore data on each disk separately. If earlier disks used to work as an array, restoring information from the whole array will be the one and only technically correct decision that will work. If you try to restore data on each disk separately, you are going to have one problem: data wouldn't be recovered.

But let’s move on to array recovery. Regarding the type of data loss you experience, whether the reason is physical damage to the drives or software errors, the steps leading you through data recovery will be similar.

Steps of RAID 5 recovery

The most basic things you need to do in order to recover RAID 5 data from one drive are:

  • Pull the disks out from NAS.
  • Connect them to the computer.

These steps will help you to save the information you had on the array and then safely transfer them to the new storage.

Steps to recover data from RAID 5

Performing RAID 5 recovery is secure and reliable with Diskinternals RAID Recovery. All you need is just to download RAID Recovery and follow the guide below.

To recover RAID 5 data, do the following steps.

  1. 1. Connect the array disks to your computer as independent local disks.
  2. 2. Launch the Diskinternals RAID recovery software.
  3. 3. To repair RAID 5, open and perform the RAID Wizard; the new RAID disk will be added to the disk list.
  4. 4. In Reader or Uneraser mode, open the logical disk, which is contained in the Hard Drives section of the disk list from the RAID disk.
  5. 5. Highlight the data and save it to some new place using the Saving Wizard.

The software is pretty simple and intuitive, so you will be able to recover data from RAID 5 with 2 failed drives if you have a basic understanding of your RAID. Your data will be restored to some new location after the process is completed.

Related articles

FREE DOWNLOADVer 6.13, WinBUY NOWFrom $249

Diskinternals RAID 5 data recovery software will help you overcome complications to recover RAID 5 array. Anyway, in case you experience any difficulties during the process of data recovery for RAID 5, email us or call our customer care team. Your issue will be resolved in a couple of moments, and you will be provided with the appropriate instructions.

Please rate this article.
443 reviews